DISH 500+ and DISH 1000+Installation Instructions
8For DISH Pro Plus LNBF assembly: Connect the tempoary cable to Port 1 (119°W) of the LNBF(seeFigure6).Figure 6: DISH Pro Plus 500+ and 1000+ LNBF
9 Table 1: Torque ValuesLocationTorque Value (ft-lbs unless otherwise noted)Pivot bolt (Mast foot; ensure no mast deformation occurs during tightenin
10Fine-tune elevation angle.Usingthepeakingmeter,ne-tunetheelevationangle.Usinga1/2”wrench,loosenthetopelevationnutontheelevatio
11For installation of the DISH Pro Plus 500+ LNBF (supports up to three receivers): Connect the cables from Port 1, Port 2, and Port 3, leaving a serv
12b. From the Node’s DPX port, connect a coaxial connection to the DPX receiver’s To Node DPX port.c. Connect the Node to the DPX receiver and t
13Thesummaryscreensbelow(seeFigures15and16)aresimilartowhatshouldbeshownforalegacy receiver connected to the DISH 500+ or DISH 1000+
14 Run Check Switch. Run Check Switchagainandconrmreceptionfor110°W,119°W,and118.7°W satellites if using DISH 500+ and for 110°W, 119°W, 129
15ZIP CodeELD500+SKD1000+SKAZ00001 15 69 71 11700002 12 77 78 12000003 17 67 69 11700004 16 71 73 12000006 15 73 76 12100007 9 77 78 11600008 26 79 83
16ZIP CodeELD500+SKD1000+SKAZ00284 21 124 126 25200285 25 127 129 25000286 31 131 134 24500401 24 126 129 25000501 24 127 130 25100544 24 127 130 2510
17ZIP CodeELD500+SKD1000+SKAZ078XX 25 126 129 248079XX 25 126 129 249080XX 26 127 130 248081XX 26 127 130 248082XX 26 128 131 249083XX 26 127 130 2480
Attention and Warning SymbolsYou must be aware of safety when you install and use this system. This guide provides various procedures. If you do some
18ZIP CodeELD500+SKD1000+SKAZ285XX 30 131 134 245286XX 33 127 130 237287XX 34 126 130 235288XX 34 126 130 236289XX 35 126 129 233290XX 34 129 133 2392
19ZIP CodeELD500+SKD1000+SKAZ324XX 40 129 133 233325XX 41 128 132 231326XX 38 133 137 239327XX 37 135 138 241328XX 37 135 139 242329XX 37 136 140 2433
20ZIP CodeELD500+SKD1000+SKAZ532XX 32 115 119 222534XX 32 116 119 223535XX 32 114 118 219537XX 32 114 118 219538XX 33 113 117 217539XX 32 114 118 2195
21ZIP CodeELD500+SKD1000+SKAZ576XX 35 102 107 194577XX 37 101 106 191580XX 32 105 110 201581XX 32 106 110 203582XX 31 104 108 200583XX 31 103 107 1975
22ZIP CodeELD500+SKD1000+SKAZ793XX 47 108 114 199794XX 47 108 114 200795XX 47 111 117 204796XX 47 112 118 205797XX 49 108 115 200798XX 51 106 113 1977
23ZIP CodeELD500+SKD1000+SKAZ835XX 37 88 93 165836XX 39 88 93 167837XX 40 88 93 167838XX 35 88 93 165840XX 42 94 99 177841XX 42 93 99 176842XX 42 93 9
24ZIP CodeELD500+SKD1000+SKAZ980XX 35 83 88 155981XX 35 83 87 155982XX 34 83 88 155983XX 35 83 87 155984XX 36 83 87 155985XX 36 82 87 154986XX 37 82 8
25Federal Communications Commission (FCC) NoticationRegulatory InformationThis device complies with Part 15 of the FCC rules. Operation is subject to
1Attention! Theseinstallationinstructionsareintendedforusebyqualiedprofessional technicians due to the complexity of the installation and co
2Quick Installation Instructions Figure 1. DISH 500+ and DISH 1000+ Antenna System Overview
31. Find Elevation/Skew/Azimuth angles for the DISH 500+ or DISH 1000+ and your location (instructions on page 4 and tables begin on page 15).2. Fi
4Locating the Antenna AssemblyUse the Reector Pointing Angles thatbeginonpage15tondtheelevation,skew,andazimuthanglesusing your locatio
5 Set skew. To access the skew bolts, loosen the elevation bolts and elevation rod nuts. Loosen the skew bolts. Set the skew by rotating the elevatio
6 Mount the reector on the mast and point the reector. Slidethereectordownontothemast.Makesuretheazimuthplaterestsontopofthemast.
7Completing InstallationUse the steps below while referring to Figure 1, page 2 for this installation.Note:UseRG-6coaxialconnectionsbetweenthea
Comments to this Manuals